Recent content by sjt47y
-
Importing my own car from another country.
Wow it's been a long time since I posted. I like to ask if anyone knows a company that can provide the service of importing my s15 from Asia. I have it sorn at the moment and lying in Malaysia. Which is such a shame. I like to bring it to the UK but just don't have the time to go through... -
Loudest exhaust
Hi can anyone tell me which exhaust is the loudest? I need some deafening exhausts as mines driving me crazy with a lack of sound! (fugitzubo currently). I am no show off but can't be a stealth rider either. Can some one point me in the right direction pls. Thanks.- sjt47y
- Thread
- Replies: 16
- Forum: Mechanical & Bodywork
-
ECU question
Hi! I have looking into ECUs recently, possibly to have a go at mapping myself. I have shortlisted the ECU i would like to decipher, have you guys heard of Proefi Ecu? Seems to be doing wonders to the supras and 350Zs. I have done some readups on the haltechs, nistunes, wolfems etc but I...- sjt47y
- Thread
- Replies: 2
- Forum: Electrical & Audio
-
S14 / S15 TPS and IACV
Hi I like to ask if anyone knows if the s14 TPS and s14 iacv fits the s15? trying to order these: http://www.frsport.com/Nissan-TPS--Throttle-Position-Sensor--Sensor-SR20DET-S14_p_25981.html http://www.frsport.com/Nissan-OEM-S14-SR20DET-Idle-Air-Control-Valve-AAC-IACV_p_12510.html looks...- sjt47y
- Thread
- Replies: 5
- Forum: Mechanical & Bodywork
-
Megasquirt
Hi there Like to ask if anyone heard of megasquirt ecu? Any good or if compatible at all for our cars? Cheers- sjt47y
- Thread
- Replies: 8
- Forum: Electrical & Audio
-
throttle body and tps
Hi, I have been experiencing car stalling problems recently. at slightly higher speeds, i clutch in, the revs drop below idle revs and sometimes just stalls. Revs are now adjusted to idle higher at 1000revs. I changed a new blow off. I have cleaned up the pipes. But still this problem...- sjt47y
- Thread
- Replies: 0
- Forum: Mechanical & Bodywork
-
torque & wastegate
Hello! Like to ask what kind of torque figures u guys have. Asking this becasue I understand from my tuner that he usually tunes for more torque than hp. Tbh, i am alittle disappointed by my hp despite the work put in. these are my figures: 395hp at 7000rpm torque 466nm at 5100rpm...- sjt47y
- Thread
- Replies: 10
- Forum: Mechanical & Bodywork
-
turbo problem
Hi everyone, want to check if anyone got garrett turbo problems from realstreetperformance? I got 2 turbos end 2010 from them, 1 for my mate, 1 for myself. My mates broke down on installation. Mine was ok then broke after tuning. They are GT2871R turbos. I just find it a hard pill to swallow...- sjt47y
- Thread
- Replies: 5
- Forum: Mechanical & Bodywork
-
uprated oil pump (not fuel pump)
Hi Guys, like to check if anyone runs an uprated oil pump? And any good? found something about GTiR pump or the PHR pump from that the driftworks car uses. But just cant find a place/website to buy it. anyone knows?- sjt47y
- Thread
- Replies: 5
- Forum: Mechanical & Bodywork
-
fuel pump + fuel collector tank
hi Guys i have a question for the more experienced owners. I bought some 800cc topfeed injectors & rail and have installed the 2871r. I am trying to push 400+ bhp. in view of this, I was recommended to have a fuel collector tank. Its the one where u have commonly installed in the boot...- sjt47y
- Thread
- Replies: 1
- Forum: Mechanical & Bodywork
-
VTC and uprated springs
Hi Guys I think this topic could have been touch many times. but cannot find answer relating to this problem that i am facing, need expert help. I know the vtc is a very common issue. further digging i think this problem can also be caused by uprated aftermarket springs. I do not recall...- sjt47y
- Thread
- Replies: 2
- Forum: Mechanical & Bodywork
-
clicking into gear
Hi! recently i have a problem pushing into gear during cold start. You push the gear to gear 1 or R position it just cannot go in. same goes for all the other gears. After much trying, it finally goes in, usually i try to engage 2nd first and use some force to get to first. i tried pumping...- sjt47y
- Thread
- Replies: 19
- Forum: Mechanical & Bodywork
-
crank shaft wear
Hi Guys, wonder if anyone heard of crankshaft wear that requires machining. My ride had some noise and we suspected it as bearings wear. We had it changed but still the noise is there. Then we think its got to do with the crank shaft wear. My mileage is about 145,000 km. Any ideas or similar...- sjt47y
- Thread
- Replies: 0
- Forum: Mechanical & Bodywork
-
Wide Body Matte Black
My s15. What do u think? :cool: cheers JT- sjt47y
- Thread
- Replies: 63
- Forum: Members Rides: Specs & Builds